Posted on 3 Comments

Bench Racing Forums

The Bench Racing Forum is the place to ask questions and have a discussion about the products we make and sell.

The forums can be found in the tool bar above and to the left, click that tab and join me in the forums.

There we can discuss the products offered, your project or just ask a question about your build. I would much rather have a conversation here than on social media pages.

Posted on 2 Comments

Interesting information!

MOOG looks like they are making the Dakota control arms now.

CarID has a page where the Passenger side is listed available

 

MOOG® - R-Series™ Front Driver Side Upper Control Arm and Ball Joint Assembly

https://www.carid.com/1990-dodge-dakota-suspension-parts/moog-r-series-control-arm-and-ball-joint-assembly-3665691174.html?parentsubmodel[]=WHEEL+DRIVE|RWD+%28Rear+Wheel+Drive%29

Right Upper – RK623220
Left Upper – RK623221

No information on lowers at this time.

Posted on Leave a comment

We have achieved a soft open

These last two years have been very interesting. The shop has been operating at very limited capacity since August of last year. We are now at a point were we can start ramping up production. Some parts are available now, but building inventory is always going to be slow.

I made the decision to stop making a few low volume parts, like the Studebaker clips. The issues now with the Mustang II spindles is going to require a redesign of a kit I have been producing for nearly 18 years. And the fixture was damaged in the move. I really don’t want to go through the trouble to redesign and build from scratch again on those. I am going to focus on the trucks more. In design right now are my un-parallel rear four bar kits. With air bag or coil over options. There will be a standard height and a Bridge Notch type. Also is a Pre-Z front suspension kit. This will get you 2″ closer to the ground for those of you wanting to lay frame/rocker.

The shops main focus is full builds. Industrial Chassis is the house brand of parts to Phoenix Hotrod Company. You can find them over at www.phoenixhotrods.com This site will remain as the focus on parts and chassis builds.

I am moving away from Facebook. The ad pushes and cultured content are just too much. Please make an account here on the website and join the forums. I do not collect data on you, will not sell your information and can focus on your questions better.

Forum

Posted on 5 Comments

Stupid viral outbreak

I apologize for the lack of updates, but we are having growing pains. The new building and the move has taken way longer to accomplish than anticipated.

First the shut down and move since the first of the year, moving the equipment to the new location in Tempe AZ and the merge with Phoenix Hotrod Company, all of which was underway when this shut down has occurred. Most of the move went fairly well, but getting the trades in the new location to do build-out of the building was slow or delayed. But the thing that is absolutely kicking our butts is the dust collection system for the plasma table.

The new location is air-conditioned. Going to be so nice for those hot Arizona summers. In fact, this past summer we broke a record of days over 100º by one day (so far) and it’s been really dry. Our Monsoon storms were non-existent this year, which was sort of a blessing as a lot of our equipment was stored outside. And as it goes, the last thing we need before we can ramp up production is the dust collector. The plasma table can really kick up some dust when we are cutting. The portable units we have for temporary use just are not capable, and I can plug up the HVAC filters in minutes. There have been promises to get this system up and running since early September, not even close. The blower fans needed haven’t even been made yet.

So the minimal cutting we can do without choking everyone out has resulted in something. As a test run, we made two of the bolt in kits for the 47-55 Chevy/GMC trucks. One is spoken for, the other is up for grabs!

The other products can resume as soon as we can. Look forward to an announcement on the www.phoenixhotrods.com page, I will have the web store up here and there as Industrial Chassis Becomes the “house brand” for PHC. And trying to talk the boss into a Grand Opening party/Throwdown/Meet-N-Greet or maybe a pancake breakfast or something.

Posted on 1 Comment

Opening Day is getting closer

I am getting really hammered with requests for product, I really want to get back to production. This COVID virus has really put the brakes on everything. We had hoped to be up and running by last month, more likely we will have things working and ready for production by mid-August now.

Posted on Leave a comment

Covid Blues

This has been one strange journey.

Since our merge with Phoenix Hotrod Company in February, the move came to a crawl. The preparation for our new location in Tempe Arizona almost ground to a halt. The electrical install has taken way longer than we anticipated. However, things are finally getting wrapped up. Machinery is finally getting placed and we hope to move the remaining equipment from the Deer Valley location of Phoenix Hotrod by mid-July. The push to get going over there is urgent.

It will likely take us a few weeks if not months to get the workflow worked out, so production may be a little slow in coming. But it looks like we will get everything back online before the end of summer and, AND new stuff also.

Posted on Leave a comment

Making use of my free time

Quarantine time

We find ourselves in strange times with this viral outbreak. My merger with Phoenix Hotrod Company is ongoing, but we are on a limited work schedule. So what am I to do with a four day weekend for the next few weeks. Normally we work a 4-10 with a nice three day weekend, but we are trying to limit exposure. By one day? Okay, that’s what the legal team wants.

Everyone is doing it, so I may as well join the fray. I’m getting back to doing my videos on YouTube. I have two of my long-term projects stored at a secret location where I can work on them over the weekend like normal folk. So naturally, I need to document it and put it on YouTube, right? The first project I am going to work on is my 1954 Ford F100. I started this years ago.

This was a farmer’s Special. Worked hard and abused to death. Was originally a standard truck with a 272 Ford Y-block and overdrive trans and heater being the only upgrades. When I got it, the frame rail on the driver side had two major breaks and some really sketchy repairs. The right side rail wasn’t much better. I pulled the frame all the way down to the rails. Designed and built a whole new fabricated center X-member, installed one of my Dakota IFS kits with 1990 Dakota parts. All powder coated and rebuild. The rear is a 1969 Dana 60.3 from a Camper Special truck. Rebuilt, all new bearings and custom axles to use the later Ford 8.8 style axle bearings, Wilwood brakes all around, Ride Tech coil overs on the rear with helper sleeve airbags and Cargo Coil springs and Bilstein Shocks on the front. The intent is to build a towpig. Like a heavy half ton truck that can comfortably tow a 24′ enclosed trailer.

Power is coming from a Cummins ISF 3.8 four cylinder turbodiesel and backed by an Allison 1000 6-speed auto.

The goal is is to make this look like it was a stock truck, but as a crew cab. Even going with the factory colors.

Follow along with the build. https://www.youtube.com/user/ELpollacko

Posted on 2 Comments

Do work son!

Yeah, things are progressing. The move is moving forward. It’s looking like about six weeks or so of this posting that we will be back.

The web-store will be back when we are able to produce. There may be a delay in between when you order and when we ship, but no more than a week as we sort the production and shipping in the new location.

This has been one of the wildest journeys so far. The potential here is going to be next level for the entire team.

Posted on Leave a comment

Update and information

The product lines are still on hold until we finish moving. We are currently merging with Phoenix Hotrod Company and will not have capacity to build you any product until that move is completed.

We are no longer at the West Osborn address, custom work will be considered at:

Phoenix Hotrod Company

1700 E. Robin Ln

Phoenix, AZ 85024

Phone for CUSTOM WORK ONLY is 602-410-1211

Please do not call and ask about product at this time!

Posted on Leave a comment

For sale,1954 F100 Crew Cab Chassis and body parts.

F100 Crew-Cab project, Frame was repaired, straightened and lengthened 29″ to build a custom crew cab.

Chassis is done, Dakota IFS with Full-size truck rotors, anti-roll bar, Wilwood D52 calipers up front. Centric StopTech and slotted and cryo-treated  rotors, new Timken bearing, new premium MOOG Problem Solver parts, powder coated, Bilstein shocks, new TRW springs, etc. The rear suspension consists of a Ford F100 Camper Special Semi-floater, Truck Dana 60, with upgraded SET20 tapered roller axle bearings, Dutchman axles, Wilwood brakes, new gears and bearings. Power-Lok diff, Ridetech coil overs and Firestone 9000 air bags for load, all on a powder coated four link with panhard rod featuring large polyurethane bushings for comfort and noise isolation without giving up control. . Hydro-boost brakes and new master cylinder. I was building this to be a long distance hauler, something that could easily pull a 20-25′ enclosed trailer.

Included are a set of 5 Wheel Vintique 17″ X 7″ steel Ford style wheels with caps and rings. Wheels are powder coated Navajo White.

If you were to contract someone to design and build an identical frame, it would exceed what I’m asking here.

Body work was started, floors are nearly complete, I have most of the body work and bed, seats, mechanicals, but in poor but fixable shape. I am currently working on the pickup and will be uploading YouTube videos of the build, follow along if your not in the market for a project like this, OR, in the end maybe you could purchase this as it nears completion. 

56 rear doors, shortened a bit. Use stock window mechanisms, keep the vent windows etc. Trying to make this look as much like a factory build as possible. This was a personal project of mine, no expense spared in the workmanship or parts used so far. 

I have an Arizona title in my name for this. And if you don’t haggle me much on this, I even have a pair of 1954 Arizona license plates to throw into the deal 

$9750.00

There are other items I have for this project not included with this sale. Example, I have a modern Cummins turbo diesel four cylinder and an Alison 1000 six speed auto that would be a fantastic power unit, but I realize it’s not everyone’s preference. I will be selling those items separately. I would consider finishing this for you as a project and may make a deal for the powertrain I had reserved for this.

Please use steve@industrialchassisinc.com for communications.