1953-64 Studebaker frame

We have been working on a complete replacement frame for the Studebaker coupe. We had built a complete frame for a customer a few years back where we integrated one of our Studebaker clips and an early C4 Corvette rear suspension. We also learned what does and doesn’t work to make a frame that fits the stock body without modification. Well, very few and simple modifications anyway. Those tiny foot-well boxes behind the front seat have got to go. What we are delivering is a frame with significant improvements in strength. And almost all the stock body mounts are located in stock locations and stock body rubbers are used. No need to alter your front fenders, stock components fit.

Straighter frame rails and more clearance for exhaust systems. We keep the entire frame profile slim for good ground clearance as well as give you room for future modifications. We made the rear kickup quite a bit different by utilizing more space under the stock floor. This gives  us better places to attach the triangulated four bars and still not have to modify the floor. This rear kick up is also slightly narrower so that if you decide to do a mini-tub on the rear you have frame clearance to run up to a 275 wide rear tire on a 9″ wheel.

Full Frame for 53-64 Studebaker coupes.

Full Frame for 53-64 Studebaker coupes.

Spies Stude build: Frame

Getting on with the full frame fabrication for Gary Spies 53 Studebaker C-Coupe.

1954 Stude Frame E

2014-06-19 16.52.22 2014-06-10 14.39.28 2014-06-19 16.51.00

Brad’s GT: 1963 Studebaker Gran Turismo

Brad came to us with this rusty Stude looking for a full frame build.

He knew the original Studebaker frames were fairly flimsy to start with and his had been laying in the mud for a few decades. After sand blasting it was obvious it wouldn’t be up to his standards. We showed him his options and work on other Studes we had here at the time and made some decisions. Mustang II with custom tubular control arms, Bilstein shocks, power rack, complete new frame with tubular center section and a narrowed C4 Corvette rear. He dropped off the original frame for us to use as an armature and the tube stared flying.

The rear axle assembly gathered most of our attention. To narrow one of these this much you lose the ability to shorten or otherwise use the stock spring. We converted the stock shock mounts to take Bilstein Coil overs and had to rebuild the steering rod assembly to clear the frame rails. I totally screwed up and didn’t get any shots of that work, I do have the 3D files of the center mount.

First up was getting the body mounts, frame contour and suspension located. We used one of our existing frame clips for the front end and mocked up the rear suspension to see if we needed any special considerations before laying out the 2X4 box tube. Mid build it was decided that we needed a few more inches of space for the rear wheels, this threw a minor wrench in the works but it all worked out.

New frame with rear installed

Corvette rear mounting

CNC plasma cut four bar brackets

Frame rear

New frame from the rear

Tie rod box bolted in place of the orignial spring mount

Frame done we got the nod to fix the rusty parts and fit the body to the frame. This also gave us a chance to change the body mounts and add some really nice bellypans. Most of the rust was concentrated in the trunk area. Both front footwells needed to be replaced and the superfluous rear seat footwells were also eliminated.

The stock firewall was lacking in style for a build this serious, same for the inner fender wells. Wes tuned up his hammers and knocked down some good stuff.

New firewall and fenderwells

I took on the custom hood hinges. In these shots you might be able to spy the firewall mounted brake power booster, inside is a custom pedal bracket with the option of adding a clutch. Wes got to do some extra detail work, the upper control arm openings got a nifty support and rubber boot.

Custom front opening hood hinges

Adjustable hinge mount

Hood in the open position

Control arm cover

Wrapping up the project before it left us, we got a few drawings from Jim Smith

Jeem's pencil scribbling

View from the rear, custom tail lights and mini-fins

Just about ready to leave us

Staged for the door, Thanks Brad!

Studebaker stampeede


Howdy folks! Been busy as all get out with Studebakers last week. We had a 1955 Commander post coupe in for a suspension upgrade and rare 1962 Studebaker Gran Turismo in for an engine swap that may turn out to be a fairly serious build.

The 55 was really straightforward. We had previously build a clip for Mr. Desenberg’s 1960 Hawk and realized we had made a mistake in pushing the suspension too far up int the chassis causing problems installing the engine. A problem with the GT I will get to in a minute. I pulled up all my Alibre’ drawings and revised them to not only correct this issue but also refined the design and now we have a production capable clip. The installation took us about 14 hours in total from remove the front sheet metal, saw off the original suspension and install the new suspension. We included a set of our tubular control arms, Granada brake upgrade and power steering rack all for $4000.00.

Photobucket

Photobucket

Studebaker clip

Mr. Metivier picked up his car just after we took in the rare Gran Turismo. Nice car on the outside. Someone had swapped the stock front sheetmetal for the older and cooler IMHO 53-54 sheetmetal. Brought in by our good customer, www.steeldreamz.com they were looking to swap out the really low mile small block Chevrolet engine and transmission for a more modern LS series and four speed automatic. As is our normal practice to do such a thing we removed the front sheet metal to get better access to the frame. This gives us more room to work and perform a more professional job. Doing this uncovered the previous owners work. They had installed a Fatman Fabrications front subframe. Due to design of this suspension clip, engine installation is nearly impossible without cutting the floor out and building a new trans tunnel and rebuilding the firewall. Sure it gets the car really low without dropped spindles but if it were designed with more forethought, similar results could have been achieved and made engine installation much easier.

This shows just how much of the inner fender needed to be cut away just to clear the upper control arms.

suspension into the right side inner fender

Rather than cut into the body further the installer decided to modify the suspension. Path of least resistance for him I am sure. However this created an entirely new problem, bumpsteer. Not only was the crossmember cut and dropped the rack and pinion was mounted lower off thick straps. Dangerous and crude, very nice combination.

Photobucket

We are still waiting for input from the customer on this one. He want’s to replace his Mercedes Benz daily driver with this car. This is something we can do for him, just not with this mess of a front end.

What is desired is a car that will drive very well, handle and brake and last as a new car would. What we would very much like to do is replace the Fatman clip with our kit. Our tubular control arms which are not only stronger but upgrade the ball joints and use OEM rubber control arm bushings for a much better ride without the polyurethane squeak and harshness. A set of Bilstein shocks and matched springs. A Flaming River variable assist rack and pinion would definitely set off the steering feel. And if there is any budget left, we would really like to rebuild the rear suspension with a torque arm system and Bilstein coil overs in the rear.

Here’s the links to the pictures:

http://s206.photobucket.com/albums/bb93/ELpolacko/1953-1962%20Studebaker%20Hawk/1955%20Commander%20Metivier/

http://s206.photobucket.com/albums/bb93/ELpolacko/1953-1962%20Studebaker%20Hawk/1962%20Studebaker%20GT%20Fatman%20Fab%20repair/

I am going to try and make this blog a weekly thing, so, until then. Adios!

Steve