Ball Joints 2.0

In my last post, covered the Chrysler style screw in ball joints commonly used on Mustang II front ends. Today I want to talk about the Dakota ball joints and some misconceptions being run around the internet. There are a few generations of Dodge Dakotas now, I concentrate on the first two, being 87-90 and 91-96. Both are pretty much the same, the ball joints are exactly the same.

I have run across a few people trying to conflate the 97 up (3rd Gen) Dakota ball joint issues with the earlier First and Second generation trucks. In the 3rd Generation Dodge made quite a few changes to the Dakota’s front suspension. Almost a complete redesign. About the only thing similar is the lower control arm spacing and bushing size (yes, they will fit our kits) and the upper control  arm rear mounting bolt is in the same location. But that’s it. The rack mounting and angles are very different and the upper control arm became symmetrical for cost cutting reasons. The other major changes are in the spindle and ball joints. They bare no resemblance to the 1st and 2nd gen trucks. The ball joints became significantly smaller and the orientation of the lower ball joint changed from tension (pointing up) to compression (pointing down) making dropped spindles pretty much impossible.

 

Have a look at the line up of ball joints here. From Left to right, the 1997 and up Dakota/Durango ball joint, The K772 Ball joint used in most Mustang II type set ups, The K778 joint used in the 87-96 Dakotas (and many other full size cars and trucks) and then on the Right is the K7025 used on the Dakotas and several other full size cars and trucks. Visual confirmation would show you, this is robust stuff. History can confirm that these larger ball joints were not failure prone. Sure, everything wears out, this is why we recommend using premium quality repair parts when building your car or truck. Not only will you see a longer service life, you will get a better ride quality with parts like the MOOG joints and bushings we suggest.

I suppose shocks would be the next topic, stay tuned!

More new product in the store

Recently added are dropped spindles, engine mounts and a few other goodies.

Like this, a bolt-in transmission crossmember for stock Model A frames. Allows you to use ’35 up style transmission mounts and a 48-52 Ford F1 brake and clutch pedal set. 

 

Quick hits from around the shop

1955-1959 GM Dakota kits very soon. AND MORE!

Been working on the design for the newest kit to our line. The 1955-1959 GM Truck Dakota kit. We will have this ready by the end of September in two forms. Our standard kit that accepts the stock ’87-’96 Dodge Dakota componentry and this will be our first venture into a tube control arm and coil over front end! Yes, you read that right we are going to offer tube control arms very soon. I have been working on the design and the fixturing to get these to a reasonable cost. So look for an official release of the newest kits very soon.

We have also been working on engine mounts and bolt on anti-roll bar mounts. I have some almost ready to go for Ford and Chevy engines in the 35-56 F100 kits. I need to check fitment on the others before we release them.

 

 

New information regarding springs and brakes

I do my best to keep up with information on all of our products. I was recently informed that the earlier 1973-1982 Dodge D series rotors for the 3000 pound front axle take a different bearing and are not compatible with the Dakota spindles. I made a quick note on the D-series caliper bracket selection about this change and will soon update all of the information to reflect the correct interchanges.

This morning however, was a question about springs for the Dakota IFS kits with 302 Fords. This is a work in progress and as I gather more information about the spring selections I will add it to the list to help you guys get the most out of your front end. This new information about the spring selection is in the Dakota Tech section.

Instruction sheets for the 65-66 F100s

I have to apologize for not getting this done sooner, but here they are. A real set of instructions for you guys.

CLICK HERE FOR THE LINK TO THE INSTRUCTIONS

New product: D-series Caliper Brackets

We have started offering the caliper brackets that allow you to use the Wilwood D52 Dual Piston caliper bracket and the larger rotor from the ’73-’93 Full size trucks on your Dodge Dakota based front end. Have a look CLICK HERE

Now available in the Store: ’53-’56 F100 Dakota kits

That’s right! Available again, the really correct IFS kit for your Classic Truck is available. The only true truck suspension kit for you classic, rack and pinion, double A-frame rugged and designed to last. The correct track width, you can use readily available and inexpensive wheels and tires, two choices of bolt patterns, including a stock 5 on 5 1/2″ to match your stock or upgraded truck rear axle.

This kit can take your abuse. Designed for heavy loads or just a nice daily driver, this kit works with most engines including heavy diesel up to 1000+ pounds. With the addition of an anti-roll bar and a performance oriented shock absorber, it will carve corners with confidence. Add a pair of dropped spindles and get the stance you want, this kit will meet the demands of most all you need.

 

Zeroing in on the 53-56 Kits

Industrial Chassis Inc Dodge Dakota based IFS Kit

Industrial Chassis Inc Dodge Dakota based IFS Kit

The first run of the newest generation Dakota kits for the 53-56 F100s will be run by the end of this week. We already have a handful of pre-orders. Look for them to be listed in the store this weekend!

New kits on the horizion

I have frames for 1953-56 Ford F100 and 1955-59 GM trucks sand blasted and ready for prototyping. Stay tuned here and on our Facebook page for updates.