Promo Video

We had Bean’s Book of Rod Shops stop by last week. These guys travel around the country and shoot video of different shops. Here is some footage they took.

Quick hits from around the shop

New product in the store!

As promised earlier, we have the 57-60 F100 and 55-59 GM truck Dakota IFS kits available in the store. These are for the stock arm Dakota suspension systems. If you want air bag systems, any of the kits that would fit any of the Dakota two wheel drive systems should work in our kit. However, we are getting hit pretty hard to do a dedicated IFS kit with tubular control arms and air bags. So we are going to do our best to get them drawn up and in production before Christmas!

Also in the works are engine mounts for the Dakota IFS kits. I think we have the Chevy engine mount systems ready to go and will be in the store in a few weeks. The Ford Windsor style mounts are still in need of some work to make them what we want. And if we can, the LIMA series (429-460) engine mounts also. These of course are going to require a rear sump oil pan to clear the rack and pinion like any other IFS kit on the market.

2015-11-13 13.38.32Keep an eye peeled for our new line of rear suspension kits too! There will be three kits ranging from near stock to work with your nearly stock Dakota IFS and a lowered kit as well as a hammered kit with a 5 plus inch C-notch built into the boxing system. These kits will be an un-parallel and unequal length four bar with a panhard rod. A moderately low roll center that works with pickups and all come with 100% anti-squat at ride height and minimal changes in pinion angle to curb any driveline vibration. Heavy duty construction with greasable polyurethane bushings and RideTECH shocks.

We are also working on the ’32 Ford chassis components, The front and rear bolt in crossmembers should be in production by mid-January. We are also considering a full bolt in X-member similar to our ’32 system for the 33-34 Ford frames. Let us know in the comment section what you think and what you would like to see in that kit.

1955-1959 GM Dakota kits very soon. AND MORE!

Been working on the design for the newest kit to our line. The 1955-1959 GM Truck Dakota kit. We will have this ready by the end of September in two forms. Our standard kit that accepts the stock ’87-’96 Dodge Dakota componentry and this will be our first venture into a tube control arm and coil over front end! Yes, you read that right we are going to offer tube control arms very soon. I have been working on the design and the fixturing to get these to a reasonable cost. So look for an official release of the newest kits very soon.

We have also been working on engine mounts and bolt on anti-roll bar mounts. I have some almost ready to go for Ford and Chevy engines in the 35-56 F100 kits. I need to check fitment on the others before we release them.

 

 

New information regarding springs and brakes

I do my best to keep up with information on all of our products. I was recently informed that the earlier 1973-1982 Dodge D series rotors for the 3000 pound front axle take a different bearing and are not compatible with the Dakota spindles. I made a quick note on the D-series caliper bracket selection about this change and will soon update all of the information to reflect the correct interchanges.

This morning however, was a question about springs for the Dakota IFS kits with 302 Fords. This is a work in progress and as I gather more information about the spring selections I will add it to the list to help you guys get the most out of your front end. This new information about the spring selection is in the Dakota Tech section.

Instruction sheets for the 65-66 F100s

I have to apologize for not getting this done sooner, but here they are. A real set of instructions for you guys.

CLICK HERE FOR THE LINK TO THE INSTRUCTIONS

New product: D-series Caliper Brackets

We have started offering the caliper brackets that allow you to use the Wilwood D52 Dual Piston caliper bracket and the larger rotor from the ’73-’93 Full size trucks on your Dodge Dakota based front end. Have a look CLICK HERE

Now available in the Store: ’53-’56 F100 Dakota kits

That’s right! Available again, the really correct IFS kit for your Classic Truck is available. The only true truck suspension kit for you classic, rack and pinion, double A-frame rugged and designed to last. The correct track width, you can use readily available and inexpensive wheels and tires, two choices of bolt patterns, including a stock 5 on 5 1/2″ to match your stock or upgraded truck rear axle.

This kit can take your abuse. Designed for heavy loads or just a nice daily driver, this kit works with most engines including heavy diesel up to 1000+ pounds. With the addition of an anti-roll bar and a performance oriented shock absorber, it will carve corners with confidence. Add a pair of dropped spindles and get the stance you want, this kit will meet the demands of most all you need.

 

Zeroing in on the 53-56 Kits

Industrial Chassis Inc Dodge Dakota based IFS Kit

Industrial Chassis Inc Dodge Dakota based IFS Kit

The first run of the newest generation Dakota kits for the 53-56 F100s will be run by the end of this week. We already have a handful of pre-orders. Look for them to be listed in the store this weekend!

New kits on the horizion

I have frames for 1953-56 Ford F100 and 1955-59 GM trucks sand blasted and ready for prototyping. Stay tuned here and on our Facebook page for updates.