We have been building and stocking some parts. Not everything is back. Here is a list of what’s in stock right now.
1953-56 Ford F100 Dakota kit
1957-60 Ford F100 Dakota kit
1961-64 Ford F100 Dakota kit
1965-66 Ford F100 Dakota kit
1947-1955 GM (AD) Dakota kit
Early Oldsmobile engine mounts
Model A trans crossmember F1 Style
1932 Ford K-legs Straight (flat floor)
1932 Ford K-legs Bent (stock floor)
1932 Ford Full X-member (stock floor)
Studebaker stuff is not on the list of products to build. Our fixturing was damaged during our move and it’s low volume enough to not want to re-create the fixture.
We are contemplating a run of tubular control arms for the Dakota to be used with coil overs. We have a special kit to work with these arms that can be ordered with the tube set that simplifies installation. Tube arms for Coil overs are going to be a bit expensive because of the limited runs. The crossmember we have special for the tube arms is a bit cheaper because there are not spring pockets. You will still need spindles, brakes, rack and pinion, and coil overs to complete the front suspension kit.
These last two years have been very interesting. The shop has been operating at very limited capacity since August of last year. We are now at a point were we can start ramping up production. Some parts are available now, but building inventory is always going to be slow.
I made the decision to stop making a few low volume parts, like the Studebaker clips. The issues now with the Mustang II spindles is going to require a redesign of a kit I have been producing for nearly 18 years. And the fixture was damaged in the move. I really don’t want to go through the trouble to redesign and build from scratch again on those. I am going to focus on the trucks more. In design right now are my un-parallel rear four bar kits. With air bag or coil over options. There will be a standard height and a Bridge Notch type. Also is a Pre-Z front suspension kit. This will get you 2″ closer to the ground for those of you wanting to lay frame/rocker.
The shops main focus is full builds. Industrial Chassis is the house brand of parts to Phoenix Hotrod Company. You can find them over at www.phoenixhotrods.com This site will remain as the focus on parts and chassis builds.
I am moving away from Facebook. The ad pushes and cultured content are just too much. Please make an account here on the website and join the forums. I do not collect data on you, will not sell your information and can focus on your questions better.
I apologize for the lack of updates, but we are having growing pains. The new building and the move has taken way longer to accomplish than anticipated.
First the shut down and move since the first of the year, moving the equipment to the new location in Tempe AZ and the merge with Phoenix Hotrod Company, all of which was underway when this shut down has occurred. Most of the move went fairly well, but getting the trades in the new location to do build-out of the building was slow or delayed. But the thing that is absolutely kicking our butts is the dust collection system for the plasma table.
The new location is air-conditioned. Going to be so nice for those hot Arizona summers. In fact, this past summer we broke a record of days over 100º by one day (so far) and it’s been really dry. Our Monsoon storms were non-existent this year, which was sort of a blessing as a lot of our equipment was stored outside. And as it goes, the last thing we need before we can ramp up production is the dust collector. The plasma table can really kick up some dust when we are cutting. The portable units we have for temporary use just are not capable, and I can plug up the HVAC filters in minutes. There have been promises to get this system up and running since early September, not even close. The blower fans needed haven’t even been made yet.
So the minimal cutting we can do without choking everyone out has resulted in something. As a test run, we made two of the bolt in kits for the 47-55 Chevy/GMC trucks. One is spoken for, the other is up for grabs!
The other products can resume as soon as we can. Look forward to an announcement on the www.phoenixhotrods.com page, I will have the web store up here and there as Industrial Chassis Becomes the “house brand” for PHC. And trying to talk the boss into a Grand Opening party/Throwdown/Meet-N-Greet or maybe a pancake breakfast or something.
I am getting really hammered with requests for product, I really want to get back to production. This COVID virus has really put the brakes on everything. We had hoped to be up and running by last month, more likely we will have things working and ready for production by mid-August now.
Since our merge with Phoenix Hotrod Company in February, the move came to a crawl. The preparation for our new location in Tempe Arizona almost ground to a halt. The electrical install has taken way longer than we anticipated. However, things are finally getting wrapped up. Machinery is finally getting placed and we hope to move the remaining equipment from the Deer Valley location of Phoenix Hotrod by mid-July. The push to get going over there is urgent.
It will likely take us a few weeks if not months to get the workflow worked out, so production may be a little slow in coming. But it looks like we will get everything back online before the end of summer and, AND new stuff also.
We find ourselves in strange times with this viral outbreak. My merger with Phoenix Hotrod Company is ongoing, but we are on a limited work schedule. So what am I to do with a four day weekend for the next few weeks. Normally we work a 4-10 with a nice three day weekend, but we are trying to limit exposure. By one day? Okay, that’s what the legal team wants.
Everyone is doing it, so I may as well join the fray. I’m getting back to doing my videos on YouTube. I have two of my long-term projects stored at a secret location where I can work on them over the weekend like normal folk. So naturally, I need to document it and put it on YouTube, right? The first project I am going to work on is my 1954 Ford F100. I started this years ago.
This was a farmer’s Special. Worked hard and abused to death. Was originally a standard truck with a 272 Ford Y-block and overdrive trans and heater being the only upgrades. When I got it, the frame rail on the driver side had two major breaks and some really sketchy repairs. The right side rail wasn’t much better. I pulled the frame all the way down to the rails. Designed and built a whole new fabricated center X-member, installed one of my Dakota IFS kits with 1990 Dakota parts. All powder coated and rebuild. The rear is a 1969 Dana 60.3 from a Camper Special truck. Rebuilt, all new bearings and custom axles to use the later Ford 8.8 style axle bearings, Wilwood brakes all around, Ride Tech coil overs on the rear with helper sleeve airbags and Cargo Coil springs and Bilstein Shocks on the front. The intent is to build a towpig. Like a heavy half ton truck that can comfortably tow a 24′ enclosed trailer.
Power is coming from a Cummins ISF 3.8 four cylinder turbodiesel and backed by an Allison 1000 6-speed auto.
The goal is is to make this look like it was a stock truck, but as a crew cab. Even going with the factory colors.
Follow along with the build. https://www.youtube.com/user/ELpollacko
Yeah, things are progressing. The move is moving forward. It’s looking like about six weeks or so of this posting that we will be back.
The web-store will be back when we are able to produce. There may be a delay in between when you order and when we ship, but no more than a week as we sort the production and shipping in the new location.
This has been one of the wildest journeys so far. The potential here is going to be next level for the entire team.