Posted on 10 Comments

So close you can taste it!

Here we are folks, #2 is installed and this is #3 and the first one to ship.

Installation is much easier than before and the frame stiffness is unmatched. I have been test fitting parts and making small corrections so that you get a high quality part you won’t have to fight to install and will enjoy for years to come.

 

Posted on 30 Comments

Making some progress

Just thought I would give you guys a little update

Rendered the frame rails, then placed all the suspension components where I needed them. Some math and a few pot of coffee later I have the basis of the new weld in kit. Enjoy the pictures.

 

Update: 2/12/2012

Been busy drawing and thinking hard to come up with solutions to manufacturing and user issues. I have tried to simplify the already simple installation to the point where it is idiot proof to install. There are slots and tabs to lock parts in place like a snap-together model car kit, no guess work and a more precise fit. Anyone with moderate welding skills and a 110V MIG welder should be able to pull this off.

 

 

 

 

 

 

Posted on Leave a comment

Ant’s 3W build

Rather than recount the whole series of the build here, I want you to follow the link over to the HAMB by clicking THIS HYPERLINK

You will get to see the whole build from beginning to end on how we build a custom fabricated hot rod.

Thanks!

 

Posted on 5 Comments

Weekend update December 17

I have been getting quite a few calls requesting not only the bolt in Dakota based IFS kit, but to bring back the weld-in kit as well.

As you know, the economy is on shaky legs right now and everyone’s finances are in shambles and I am not immune from this. We have a few internal jobs we need to work through to get to these kits. If the response stays strong as it has I will get some motivation to build the fixtures and get this project under way.

1948-1952 Ford F1 GEN II
Posted on Leave a comment

Arizona Deuce Day 5

Started by my other Dad, Ron Olmstead, this show is turning out to be quite a thing. Now run by George Walker (also former customer) it is held at the Sanderson Ford dealership.

Arizona Deuce Day 5
Sanderson Ford Starliner Diner
5111 West Maryland Avenue
Glendale, AZ 85301

Saturday, October 29 10 AM to 3 PM

And Joel and I will be there with Anthony’s 3W and a few of our rear K-member legs will be on display. Stop on by and enjoy the cars and see Anthony’s car in person before it goes home to Alabama.

phone pix

Posted on 2 Comments

Killing the myth of the Grade 5 bolt.

There are so many old wives tales inside of the hot rod world. It particularly makes my blood pressure rise a bit to see a semi-mainstream media publication let one of their editorial writer, who happens to own one of the most recognized hot rod name brands, continue to enumerate and lend legitimacy to those myths.

 

Most of these are pretty harmless, but to state that a grade five bolt is preferred over a grade 8 bolt when mounting suspension components is really dangerous. This from the September 2011 Goodguys Gazette,. written by Brent Vandervort.

 

In actual fact, Grade 5 bolts are often preferred over Grade 8 . A Grade 8 has a very high tensile strength, but can be brittle. In applications such as suspensions, a very high number of load/unload cycles can produce work hardening, which produces an immediate, or catastrophic failure. It’s often much safer to use a Grade 5 bolt which will bend, thus providing a warning, rather than a Grade 8 bolt breaking without warning. As long as the Grade 5 bolthas been sized large enough to take the expected load, we don’t want to trade toughness (resistance to stress cycles) for the ultimate tensile strength of the Grade 8 fastener.

 

While he did leave himself a caveat with the statement of properly sized hardware for the task at hand, this subject has been debated and discussed on numerous message boards. Google for yourself and read the threads if you are interested.

I have read numerous pages of information regarding this subject because logically it never made sense that a “softer and malleable bolt” GR5 would ever be superior “than a hard and brittle bolt” GR8. What in the hell is the purpose of even making bolt with higher gradings than the 5, why would anyone make a brittle bolt?This makes no logical sense.

And furthermore, the issue of toughness. Why would a bolt of a lower grade be “tougher” and therefore more resistant to stress cycles than one of a higher grade that is stronger in tensile strength? Again, this make no logical sense.

Well, when logic fails the observations of these wives tales something is obviously wrong. Using this reasoning, an even lower grade bolt than a 5 might even be preferred because its even more malleable therefore tougher, cough. I can visit websites like SAE and BoltScience and get true and factual, means tested information without the hotrodder spin.

 

Please, if you are even remotely interested in this, open and bookmark these websites and tables.

 

The Engineers Handbook

Bolt Science

 

This thread on Pirate 4X4 is a very enlightening read, posts #9 and the response from Billavista #11 fit the discussion to a T. And here is the summary if you don’t care to click:

 

Then there’s fatigue strength. Bend a piece of metal back and forth a bunch of times; it may not break right at first, but it will break eventually. For any given metal, there is a fatigue limit, which is lower than the ultimate load. Below the fatigue limit, bend it as many times as you want and it won’t break; above that, it will eventually break. Again, in general, the higher the ultimate strength, the higher the fatigue limit.

Finally there’s impact loading. This is tested by notching a steel bar and hitting it with a hammer (very precisely, of course). This is the one case where a softer steel might do better, as harder materials tend to be more brittle. However, for most of our applications it’s not that important (unless you’re running a snowplow or trying to snatch a stuck Jeep out with a chain instead of an elastic nylon strap), as the suspension tends to damp out and spread loads below the sharp spike necessary for impact failure. Also, even grade 8 bolts aren’t all that brittle; after they’re heat treated to get the ultimate strength up they’re tempered to bring back the impact strength. Impact strength might be an issue if something’s loose, so that it shifts and bangs around before it hits whatever is stopping it (i.e. the loose bolt).

Conclusion: grade 8 bolts are stronger in virtually any application on a Jeep. Whether you need that strength, and want to pay extra for it, is another issue (though I bought some 5/16 grade 8’s yesterday for $0.60 each; grade 5’s were only ten cents cheaper). There may also be situations where you may want the bolt to fail before the expensive part it’s holding breaks, but that’s another issue. ”

 

 

As Billavista said, Grade 8 bolts are stronger. The scientific data supports it and real world testing proves it. Brent is wrong and has done damage to the hot rod community for pushing such an ignorant myth.

I have a challenge for proponents of GR5 being better suited for suspension use to find one or more makes of mass produced cars or trucks that use lower graded hardware on suspension components, take a picture and send them to me or post them here or somewhere public where we can see the evidence.

 

It is far more important to size and properly torque your hardware than any chemical or mechanical thread lockers can overcome.

Posted on Leave a comment

Kickbases

I built a few of these for myself, but as good news travels fast, people found out about them and wanted them. I built them with some future-proofing as best as I could see by making the foot pedal for pullrod or pushrod configuration. Also putting in ten different axle pivot positions so you can choose the leverage you want.

I had ordered an Eastwood deep throat shrinker stretcher with stand to fulfill an immediate need during the chop on Richard’s Four-door Mercury and man was I ever disappointed. It didn’t even work as shipped without modification, the pullrod was about 4 inches short of working AND it needed to be bolted to the floor. Or at least a large plate that would be a pain in the ass to move about the shop. I needed mobility and stability. So a few hours of dreaming on my Alibre’ software and I came up with a base that would meet my needs.

Alibre' design of the Kickbase

Postprocessed the files and CNC cut the plates out of 1/4″ steel plate and TIG welded my prototype machine together. This first unit had a solid body 3/8″ foot pedal on it and I used a clevis to connect the pullrod. I found out shortly some limitations to this design so I cut a pair of 3/16″ plates and was able to use a HEIM joint instead of the clevis. This freed up the feel and gave me the range of adjustability I needed. The arm pivots on bronze shoulder bushings and has a 3/4″ axle retained by a pair of snap rings. With every hole reamed to size, changing pivot positions was fairly easy to do. Once I found the arc and foot position that felt the most comfortable I threaded some heavy wall tube and welded on a six pointed thumbwheel. This also was changed out to a lighter setup and I added a pair of counter springs to the back of it to improve the pedal feel, it was just too light and was far to easy to over shrink the workpiece.

First mockup of the prototype

It didn’t take us long to put it into use…

In use on the Merc project

 

 

The most recent one out the door went to our new friend Douglas, member of the Arizona Artist Blacksmiths. He had me build an adapter to work with his Lazze branded Shrinker/Stretcher. I machined an aluminum base adapter and fabricated a new upper clevis to attach to the Lazze piece. I have these on file and can produce them for your machine also.

 

 

Other than the minor updates to the foot pedal arm and the pullrod itself, the design has worked fantastic. There are 7 of them in the world now with two available right now. Hit the E-store if your interested in one.

Posted on Leave a comment

1959 Chevy truck frame for Bruce

Bruce had bought a kit from Morrison A&M for his truck and had done the majority of the installation himself. He didn’t realize just how much work those universal kits take to install. So he contacted us to check his work and if it was good to TIG weld everything in place. When he dropped it off, we discussed what had been done and what needed to be done. The frame still needed boxing plates for the front and for the rear plates to be final welded. I offered to build a tubular crossmember system just like the ones we built for our frames and Bruce went for it.

Brian and I set off on a metal flinging frenzy of crossmember removal, cutting, grinding and tube bending. A bit more measuring and I placed the engine and trans then fabricated a nifty set of engine mounts that clear the steering rack and pinion. Thirty plus hours later, we had this!



Posted on Leave a comment

Fab-table fab

Been a busy few months here, this spring has been interesting for sure.

We had been without a large fab table since Adam pulled up stakes last year. The small setup table had been good enough for the last year but now we have new jobs coming in and the need for a new table was paramount. I prefer a larger flat sheet table with threaded holes for attaching fixtures and clamping down components, the last table had random holes that fit the individual fixtures I built, the new one has a grid for more universal measurement and hold downs.

I started off by deciding exactly how large I wanted it to be. My last table was 4X16 foot and was perfect for building narrow classic truck frames. It was a bit narrow for some of the other cars we were contracted to build. This new table is 5X12 and only 20″ off the floor. The deck is 1/2″ A36 steel and reasonably flat and the frame is made from 8″X 1/4″ channel iron.

Here is a few drawings of what I intended to build.

 

While waiting for the steel to show, I plasma cut all the legs and cut all the gusset tubing and reinforcing materials.

Just as I wrapped up the cutting and the new top and beams showed up and got to cutting the beams into the correct lengths and then cut forklift holes for moving in the future and a series of “keyholes” in the side beams to attach different fixtures or just chain binders for straightening, repair or just holding down unruly frames and assemblies.

With all the parts cut and prepped, the layout begins and the sub assemblies get welded up and test fit.

Now the real assembly begins, I started by squaring one end and inserting the end gusset tubing and welded it solid.

I then installed the first of the two center support beams, squared it, diagonally measured it and welded it in place. Then moved to the second support beam and did the same procedure.

Last was the other end beam and gusset. It went in surprisingly well, only needing a bit of tension to take the twist out of the side beams. Of course I diagonally measured each cell of the frame as I went and also checked for squareness overall. It was square to less than 1/16″.

Frame done and square I installed the center leg and support then the four perimeter legs. Rolled it over and welded everything from the top.

Quick coat of paint and install the swivel feet, level the frame and put it in it’s final resting place.

The table top was placed on the frame and as luck would have it, my plate was very flat. Only minor waves which was a bit of a surprise. Instead of welding the top to the frame I decided to bolt it down with flat head hardware tapped into the frame. Four holes on each of the end beams and the two center beams hold it in place nicely. I also scored a heavy centerline mark in the surface to aid in building and fabricating.

The last task before put into use was to drill and tap 168 1/2-13 holes in the table surface.

 

Now the fun begins! Building new fixtureing and tooling. But at least we have a solid base to work from now.